Get Mounted Starlink Gen 3 Router - Power Holder – Installation Guide

Get Mounted Starlink Gen 3 Router and Power Holder wall mounted installation

Get Mounted Starlink Gen 3 Router & Power Holder – Installation Guide

This guide is based on the product information provided by Get Mounted and standard Starlink Gen 3 installation practices. (Get Mounted)

Overview

The Get Mounted Starlink Gen 3 Router & Power Holder is designed to securely mount both the Starlink Gen 3 router and power supply in a single compact assembly. It helps reduce cable clutter, improves airflow around the equipment, and creates a cleaner, more professional installation. (Get Mounted)

Suitable Installation Locations

  • Homes and offices

  • Caravans and RVs

  • 4WD touring vehicles

  • Off-grid cabins

  • Equipment racks

  • Workshops and sheds

  • Remote communications setups (Get Mounted)

Before You Start

What's Included

  • Get Mounted Starlink Gen 3 Router & Power Holder

  • Mounting hardware

  • Installation components (Get Mounted)

Recommended Tools

  • Drill/driver

  • Drill bits suitable for your mounting surface

  • Phillips screwdriver

  • Pencil or marker

  • Spirit level

  • Tape measure

Installation Steps

Step 1 – Choose a Mounting Location

Select a solid mounting surface that:

  • Is close to a power outlet

  • Allows easy routing of the Starlink dish cable

  • Has adequate ventilation around the router and power supply

  • Is protected from direct water exposure if installed indoors

  • Provides easy access for servicing

Recommended mounting height: Eye level or above where practical.

Tip: Leave at least 50–100 mm clearance around the unit to maintain airflow.

Step 2 – Test Fit the Equipment

Before drilling:

  1. Place the Starlink Gen 3 router into the router section of the holder.

  2. Position the Starlink power supply in its designated holder area.

  3. Confirm cable ports remain accessible.

  4. Check cable routing paths.

The holder is specifically designed for the Starlink Gen 3 router and power supply. (Get Mounted)

Step 3 – Mark Mounting Points

  1. Hold the bracket against the wall.

  2. Use a spirit level to ensure it is straight.

  3. Mark the mounting hole locations.

  4. Remove the bracket.

Step 4 – Drill Mounting Holes

Timber Surface

  • Drill pilot holes.

  • Proceed directly with supplied screws.

Plasterboard or Masonry

  • Drill holes suitable for supplied wall anchors.

  • Insert anchors before mounting.

Step 5 – Secure the Holder

  1. Align the holder with the drilled holes.

  2. Install mounting screws.

  3. Tighten until secure.

Do not overtighten, as this may damage the mounting surface or bracket.

Step 6 – Install the Power Supply

  1. Slide or place the Starlink power supply into the lower section of the holder.

  2. Ensure it is fully seated.

  3. Verify ventilation openings remain unobstructed.

The open-frame design is intended to improve cooling and airflow. (Get Mounted)

Step 7 – Install the Router

  1. Position the Starlink Gen 3 router into the router section.

  2. Ensure it sits securely within the holder.

  3. Confirm all ports remain accessible.

Step 8 – Route and Connect Cables

Connect:

Dish Cable

  • Connect the Starlink cable from the dish to the power supply.

Router Cable

  • Connect the router to the power supply using the supplied Starlink cable.

Power Cable

  • Connect the power supply to mains power.

Route all cables through the integrated cable management channels where available. (Get Mounted)

Step 9 – Power On

  1. Plug the power supply into a power outlet.

  2. Wait for the Starlink system to boot.

  3. Allow several minutes for the router and dish to establish a connection.

Follow the Starlink app setup process if the system has not already been configured. (Starlink)

Final Installation Check

Verify:

☐ Holder is firmly attached to the wall
☐ Router is seated correctly
☐ Power supply is secure
☐ Cables are tidy and strain-free
☐ Ventilation openings are unobstructed
☐ System powers on normally
☐ Internet connection is operational

Cable Management Tips

For the cleanest installation:

  • Route excess cable behind cabinetry where possible.

  • Use cable ties or Velcro straps.

  • Avoid tight cable bends.

  • Keep power and data cables neatly separated.

  • Leave a small service loop near connections for maintenance.

Troubleshooting

Router Not Powering On

  • Check mains power connection.

  • Confirm all Starlink connectors are fully seated.

  • Verify the power supply LED status.

Poor Wi-Fi Coverage

  • Relocate the router higher if possible.

  • Avoid mounting inside metal cabinets.

  • Keep clear of large appliances or electrical interference sources.

Equipment Running Warm

  • Ensure airflow around the holder is not blocked.

  • Do not cover the router or power supply.

  • Verify ventilation slots remain exposed.

Product Features

  • Purpose-built for Starlink Gen 3 router and power supply

  • All-in-one mounting solution

  • Integrated cable management

  • Improved airflow and ventilation

  • Heat-resistant construction

  • Pre-drilled mounting points

  • Compact, space-saving design

  • Suitable for fixed and mobile installations (Get Mounted)

Result: A clean, professional Starlink installation with reduced clutter, improved cable management, and secure mounting of both the router and power supply. (Get Mounted)

 

https://getmounted.com.au/products/starlink-gen-3-wall-mount?variant=52870461292853